Lease this WebApp and get rid of the ads.
Harry
PHILIPS
Wed Dec 24, 2003 12:02pm
24.235.162.109

PHILIPS
N/A
27P1
RADIO INTERFERENCE,DOTS,SWIRLS OR HERRINGBONE SEEN ON PIP VERSIONS.
CHECK/REPLACE PIP MODULE (ISOLATE BY UNPLUGGING J602)

PHILIPS
N/A
25P606
Horz Lines and Vertical Roll. Clears up after 15-20 min. Repeats after turn off for several hours
Excess B+,154v, at pin 4 of IC401(STK30130) should be 130v. High B+ causes excess High Voltage, activates HV Shut-dn(Horz sync). Defective C432(100ufd/200v) (high ESR >7, should be <1). ESR drops as cap heats up.)

PHILIPS
N/A
27P1
SET IS SHUTTING DOWN
CHECK/REPLACE R11 (CRT BOARD) FOR OPEN

PHILIPS
N/A
27P1
NO VIDEO
CHECK/REPLACE C608 FOR SHORT AND R622 FOR OPEN

PHILIPS
N/A
27P1
HIGH PITCHED SQUEAL FROM POWER SUPPLY WHILE ON
REPLACE L421 USING ONLY P/N 483515757054

PHILIPS
N/A
27P1
SET SHUTS DOWN BUT WITH SCREEN CTRL. ALL THE WAY DOWN, THE SET WILL REMAIN TO RUN WITH WHITE SCREEN WITH RETRACE.
CHECK/REPLACE R11 (100 OHM) ON THE CRT BOARD -- (200 VOLT SOURCE)

PHILIPS
N/A
27P1
NO VERTICAL SWEEP
CHECK/REPLACE R445 FOR OPEN

PHILIPS
N/A
27P1
JAIL BARS ON THE LEFT SIDE OF THE SCREEN
CHECK/REPLACE L502 WITH NEW TYPE (483515757336)

PHILIPS
N/A
27P1
SET GOES OFF INTERMITTENTLY--APPEARS TO SHUTDOWN
CHECK FOR CORRECT SETTING OF THE B+ (130 VOLTS)

PHILIPS
N/A
27P1
130 VOLT SOURCE IS TOO LOW
CHECK/REPLACE R431 AND IC400

PHILIPS
N/A
27P1
NO COLOR ON SOME CHANNELS-INT. LOSS OF COLOR
CHNG. C620 TO 10pF

PHILIPS
N/A
27P1
NO COLOR WHEN COLD
REPLACED CHROMA/LUMA IC650

PHILIPS
N/A
27P1
NO HORZ. DRIVE FROM PIN 26 OF IC200
CHECK/REPLACE C222 FOR OPEN

PHILIPS
N/A
27P1
REPEATED FAILURE OF Q420 (FET)
CHECK/REPLACE C412 WITH A 100nF (MAY HAVE A 10nF FROM THE FACTORY)

PHILIPS
N/A
27P1
NO COLOR AND VOLTAGES ON IC600 PINS#12,13,14 ARE LOW
CHECK/REPLACE IC600

PHILIPS
N/A
27P6
VERY SNOWY PICTURE AT 0dB SIGNAL LEVEL
CHECK/REPLACE R222 OPEN (12k) (P/N# 483511657397)

PHILIPS
N/A
27P6
VERTICAL BOUNCE/JUMP/JITTER/ROLL ON VCR PLAYBACK
CHANGE C682 TO ).22uF POLY (P/N# 483512147002) AND CHANGE R382 TO A 1m (P/N# 483511057204)

PHILIPS
N/A
27P6
CLOCK RUNS TOO FAST AND 'VOLUME LIMITER' FEATURE IS MISSING FROM THE MENU
REFER TO THE SERVICE MANUAL FOR PROCEDURES ON SETTING THE FEATURE WORD SETTING -- IT SHOULD BE SET TO 'HEX 25'

PHILIPS
N/A
27R1
DIAGONAL LINES IN PIX OR SPOTS
CHECK VALUE OF C443--IT SHOULD BE 47pF

PHILIPS
N/A
27R1
VERTICAL ROLL ON SOME CABLE CHANNELS
CHANGE R603 TO A 2k

PHILIPS
N/A
27R1
NO OSD
CHECK/REPLACE R524 AND C525

PHILIPS
N/A
27R1
DARK LINE TO THE LEFT OF THE COLOR PIP IMAGE RUNNING THE HEIGHT OF THE PIP BORDER
CHECK/REPLACE THE PIP MODULE

PHILIPS
N/A
27R1
DEAD SET - WILL NOT TURN ON - APPEARS TO BE A RESET PROBLEM
CHECK/REPLACE C460

PHILIPS
N/A
27R1
POPPING OR CLICKING THROUGH SPEAKERS WHEN CHANGING THE SETTING OF THE VOLUME CONTROL.
CHECK/REPLACE IC120 AND IC160

PHILIPS
N/A
27R1
WHENEVER SERVICING THE R1 CHASSIS
CHECK FOR PRESENCE OF C443 (BE SURE ITS 47pF)

PHILIPS
N/A
27R1
VERTICAL WHITE LINE ON LEFT SIDE OF SCREEN
CHECK VALUE OF R502 (33K) AND R509 (470K)

PHILIPS
N/A
27R1
NO SOUND BUT DOES HAVE A HISS OR HUM IN SPEAKERS
CHECK/REPLACE C205 (0.01uF SMD)

PHILIPS
N/A
27R1
NO LUMINANCE,OUT OF SYNC,SOUND OK AND CHROMA OK
CHECK/REPLACE R623 FOR OPEN

PHILIPS
N/A
27R1
WAVY LINES OR HUM BARS IN PICTURE AND MAY JITTER
CHECK/RE-ADJUST 130V SOURCE WITH R462

PHILIPS
N/A
27R1
NO VIDEO - NO SYNC BUT CHROMA AND SOUND IS OK
CHECK/REPLACE R623

PHILIPS
N/A
27R1
DEAD SET
CHECK/REPLACE Q501 (483513047061)

PHILIPS
N/A
27R1
NO VERTICAL SWEEP OR REPEATED VERTICAL FAILURES
CHECK/REPLACE IC550 AND R553 (R553 SHOULD BE REPLACED WITH A 2 OHM 1/2 W LEADED TYPE RESISTOR)

PHILIPS
N/A
27R5
VERTICAL BOUNCE/JUMP/JITTER/ROLL ON PREMIUM DECODED CABLE
CHANGE C682 TO 0.22uF POLY (P/N# 483512147002), ADD 1.2m (P/N# 483511057204) FROM JUMPER B57 TO B40

PHILIPS
N/A
27R5
SOUND IMAGE CUTS IN/OUT ON MONO STATIONS - CUSTOMER COMPLAINS 'STEREO CUSTS OUT'
CHECK/REPLACE IC300 (P/N# 483520988462)

PHILIPS
N/A
27R5
TUNER SEARCHES IN THE CABLE MODE
CHECK/REPLACE C273 (0.01uF) (P/N# 483512247098)

PHILIPS
N/A
27R5
JAIL BARS IN VIDEO
DRESS RGB LEADS FROM CHASSIS TO CRT BOARD

PHILIPS
N/A
27R5
ERRATIC RANDOM FUNCTIONS OR WRONG FUNCTIONS FOR BUTTONS PUSHED
CHECK/REPLACE FOR LEAKY KEYBOARD SWITCH (P/N# 483527657004)

PHILIPS
N/A
27R5
BOUNCE IN THE PIP PICTURE
CHECK/REPLACE Y1002 (P/N# 483515397004)

PHILIPS
N/A
27R5
LITTLE OR NO CLOSED CAPTION INFORMATION WHEN PLAYING BACK A RECORDED CABLE PROGRAM
CHANGE C682 TO 0.22uF POLY (P/N# 483513147002) AND CHANGE C358 TO 1uF (P/N# 483512147406) (NEG. TO IC300-#23)

PHILIPS
N/A
27R5
ERRATIC OPERATION - SELF ACTIVATION OF CHANNELS,ON/OFF, VOLUME - INTERMITTENT PROBLEM
CHECK/REPLACE KEYBOARD SWITCHES (LEAKY) (P/N# 483527657004) WHICH INCLUDES ALL 7 SWITCHES

PHILIPS
N/A
27R5
PIP VIDEO HAS VERTICAL JITTER ON SOME CHANNELS
REMOVE C1036 AND SHORT WITH A JUMPER

PHILIPS
N/A
27R5
VERTICAL JITTER ON SOME CABLE CHANNELS
CHECK/REPLACE C682 WITH 0.22uF @ 100v (P/N# 483512147038) DO NOT USE AN ELECTROLYTIC

PHILIPS
N/A
27R5
NO SOUND - PICTURE IS FINE
CHECK/REPLACE R444 (2.2 @ 1/2w) AND IC702 (LA4270)

PHILIPS
N/A
27R5
OSD HAS WRONG LETTERS, WRONG SPELLING OR INCORRECT SPACING
CHECK/REPLACE IC300 (P/N# 483520988385)

PHILIPS
N/A
27R5
SOUND IS RASPY OR SLURRED OR HISSES WITH SOUND IMAGE TURNED ON AND STEREO TURNED ON
REMOVE C722

PHILIPS
N/A
27R5
LEFT AUDIO INPUT IS DEAD
SOUND IMAGE IS TURNED ON - THE RIGHT CHANNEL IS DESIGNED FOR MONO INPUT

PHILIPS
N/A
27R5
PIP PICTURE JITTERS VERTICALLY
CHANGE C1028 WITH 0.047uF (P/N# 483512287503)

PHILIPS
N/A
27S1
DEAD SET OR MULTIPLE FAILURES OF R407 ****** THIS SET CANNOT BE RAN ON LOW AC ******
CHECK/REPLACE R407 (483511687002) AND T502 (483514247015)

PHILIPS
N/A
27S1
NO AUDIO OR INTERMITTENT AUDIO
CHECK/REPLACE Y220 OR COLD SOLDER CONNECTIONS

PHILIPS
N/A
27S1
NOISY BACKGROUND OR OVER PEAKED VIDEO
CHANGE R609 TO A 2.7k

PHILIPS
N/A
27S1
SHADING ON THE RIGHT SIDE OF THE PICTURE
CHECK/REPLACE C399 (P/N# 483512217002) - A FEW SETS WERE SENT OUT WITH A 1k RESISTOR IN PLACE OF THE CAPACITOR

PHILIPS
N/A
27S1
REPEATED SEARCHING IN THE CABLE MODE
CHANGE R241 TO A 680k (P/N 483511067143)

PHILIPS
N/A
27S1
FAILURE OF IC430
CHECK/REPLACE IC430 AND Q400 FOR OPEN - ALSO CHECK THE SOLDER CONNECTIONS ON Q400

PHILIPS
N/A
27S1
TOTALLY DEAD
CHECK/REPLACE IC430 (STR30130)

PHILIPS
N/A
27S1
SHORT VERTICAL SWEEP - ABOUT 2'
CHECK/REPLACE R565 FOR OPEN

PHILIPS
N/A
27S1
SET GOES INTO SHUTDOWN - MAY STAY ON WITH HORZ. LINES OR TEARING IN THE PICTURE
CHECK/REPLACE C432 (100uF @ 200v)

PHILIPS
N/A
27S1
DEAD SET - NO ATTEMPT TO START
CHECK/REPLACE R435 (130k ) FOR OPEN

PHILIPS
N/A
27S1
REPEATED OR EARLY FAILURE OF IC430
CHECK/REPLACE Q400

PHILIPS
N/A
27S1
DEAD SET - F401 BLOWN AND AFTER REPLACING R432 BURNS
CHECK/REPLACE IC430 AND R432 (1K )

PHILIPS
N/A
27S1
HUM OR AUDIO BUZZ OR DISTORTED AUDIO
CHECK TO SEE IF C464 IS A 100uF AND C465 IS A 1000pF ( THESE HAVE BEEN INTER-CHANGED ON SOME CHASSIS )

PHILIPS
N/A
27S1
NO TUNING ON CHANNELS 15-20 - ALL OTHERS OK
CHECK/REPLACE TUNER (483521047006)

PHILIPS
N/A
27S1
R407 FAILS FOR NO APPARENT REASON AND Q403 MAY ALSO BE BAD
CHECK/REPLACE R407 (ONLY P/N 483511687002) - ADD 6.8k IN PARALLEL W/Z406 - CHNG. R502 TO 300 ohm-REPL. Z411 W/2.7k

PHILIPS
N/A
27S1
WEAK VIDEO - WASHED VIDEO
CHECK/REPLACE Q210

PHILIPS
N/A
27S4
TOTALLY DEAD
CHECK/REPLACE IC430 (STR30130)

PHILIPS
N/A
27S4
DEAD SET OR MULTIPLE FAILURES OF R407 ****** THIS SET CANNOT BE RAN ON LOW AC ******
CHECK/REPLACE R407 (483511687002) AND T502 (483514247015)

PHILIPS
N/A
27S4
DEAD SET - NO ATTEMPT TO START
CHECK/REPLACE R435 (130k ) FOR OPEN

PHILIPS
N/A
27S4
REPEATED OR EARLY FAILURE OF IC430
CHECK/REPLACE Q400

PHILIPS
N/A
27S5
VERTICAL BOUNCE/JUMP/JITTER/ROLL ON PREMIUM DECODED CABLE
CHANGE C682 TO 0.22uF POLY (P/N# 483512147002), ADD 1.2m (P/N# 483511057204) FROM JUMPER B57 TO B40

PHILIPS
N/A
27S5
BOUNCE IN THE PIP PICTURE
CHECK/REPLACE Y1002 (P/N# 483515397004)

PHILIPS
N/A
27S5
LITTLE OR NO CLOSED CAPTION INFORMATION WHEN PLAYING BACK A RECORDED CABLE PROGRAM
CHANGE C682 TO 0.22uF POLY (P/N# 483513147002) AND CHANGE C358 TO 1uF (P/N# 483512147406) (NEG. TO IC300-#23)

PHILIPS
N/A
27S5
SOUND IMAGE CUTS IN/OUT ON MONO STATIONS - CUSTOMER COMPLAINS 'STEREO CUSTS OUT'
ENTER SERVICE MODE (062596-MENU),POSITION CURSOR ON LEFT HAND '00',ENTER 3-7,ADD 8 TO 1ST DIGIT ON FAR RT.(ie OA=8A)

PHILIPS
N/A
27S5
SOUND IS RASPY OR SLURRED OR HISSES WITH SOUND IMAGE TURNED ON AND STEREO TURNED ON
REMOVE C722

PHILIPS
N/A
27T1
DEAD SET - NO ATTEMPT TO TURN ON
CHECK/REPLACE Q502 (P/N# 2SD1555)

PHILIPS
N/A
27T1
JAILBARS ON LEFT SIDE OF SCREEN
CHANGE L502 TO (P/N# 483515757673) AND L602 & L610 TO (P/N# 483515057004) COMB MODELS ONLY

PHILIPS
N/A
27T1
NO VERTICAL SWEEP
CHECK/REPLACE R445 FOR OPEN (1 1/3 WATT)

PHILIPS
N/A
27T1
REPEATED FAILURE OF Q501
CHECK/REPLACE WITH CORRECT VALUE - SHOULD BE 1.8k,3watt P/N (483511667099)

PHILIPS
N/A
27T1
AFTER CUSTOMER SETTINGS ARE SET (COLOR,TINT,LANGUAGE,ETC) AND POWER IS SHUT OFF OR SET UNPLUGGED, SETTINGS ALL CHANGE
CHECK/REPLACE IC351 (P/N# 483520988104)

PHILIPS
N/A
27T1
NOISY PICTURE-OVER PEAKED-TOO SHARP
CHANGE R331 TO A 5.6k (483511137112)

PHILIPS
N/A
27T1
BRIGHT SCREEN WITH RETRACE LINES
CHECK/REPLACE R669 FOR OPEN

PHILIPS
N/A
27T1
BLACK AND WHITE PIP MODULE FAILS TO OPERATE
CHANGE C21 TO 27pF (P/N# 483512287029) AND C23 TO 18pF (P/N# 483512287048)

PHILIPS
N/A
27T1
DISTORTED AUDIO OR STATIC IN THE AUDIO
CHECK/REPLACE R270 AND R271

PHILIPS
N/A
27T1
JAILBARS ON LEFT SIDE OF SCREEN
CHANGE L502 TO (P/N# 483515757673) AND L610 TO (P/N# 483515057038) NON-COMB MODELS ONLY

PHILIPS
N/A
27T1
NO VERTICAL SWEEP
CHECK/REPLACE IC550 AND SMD R563 - ALSO VERIFY THAT C546 IS A .01uF @ 100V AND NOT A .1uF

PHILIPS
N/A
27T1
CLOCK RUNS TOO FAST OR LOSES TIME
CHANGE R388 TO A 16k 2 watt RESISTOR

PHILIPS
N/A
27T1
NO PICTURE - HAS OSD AND SOUND - PICTURE MAY COME IN IF THE PIP BUTTON IS PRESSED ON REMOTE - SET DEFAULTS TO SPANISH
CHECK/REPLACE IC351 (P/N# 483520947113)

PHILIPS
N/A
27T1
VERTICAL BOUNCE/JUMP/JITTER/ROLL ON VCR PLAYBACK
LOWER THE VALUE OF THE RESISTOR FROM PIN#28 OF IC200 TO GROUND - ONLY LOWER ENOUGH TO CORRECT (ORIGINAL VALUE 33k)

PHILIPS
N/A
27T1
DEAD SET OR LOCKED UP - REMOVING AC MAY CAUSE SET TO START
CHECK/REPLACE IC400 (P/N 483513097006)

PHILIPS
N/A
27T1
JAIL BARS - DARK VIDEO ON THE LEFT SIDE OF SCREEN
CHANGE L502 TO 483515757673, L602 TO 483515057004, L610 TO 483515057004 (FOR COMB) AND L610 TO 483515057038 (NON-COMB)

PHILIPS
N/A
27T1
DEAD SET OR INTERMITTENT
CHECK/REPLACE T501 OR MAY HAVE POOR CONNECTIONS

PHILIPS
N/A
27T1
WHEN SET IS TURNED ON, Q501 SHORTS AND R504 OPENS
CHECK/REPLACE Q501,R504 AND T501

PHILIPS
N/A
27T1
INTERMITTENT DEAD SET OR SHUTS OFF AFTER WARM
CHECK/RESOLDER CONNECTIONS ON T501

PHILIPS
N/A
27U1
DEAD SET
CHECK/REPLACE R444 (P/N# 483511057087)

PHILIPS
N/A
27U1
PICTURE BLOOMS AND POOR 130 VOLT REGULATIONS
CHECK/REPLACE R424 AND R425

PHILIPS
N/A
27U1
NO TUNER AUDIO
CHECK/REPLACE C102 (P/N# 483512287073)

PHILIPS
N/A
27U1
NO PIP OR OSD - VERTICAL BAR DOWN LEFT SIDE OF SCREEN
CHECK/REPLACE R524 (P/N# 483511687002) AND C525 (P/N# 483512497027)

PHILIPS
N/A
27U1
INTERMITTENT OR NO COLOR
CHECK/REPLACE C661 (P/N# 483512287063)

PHILIPS
N/A
27U1
DARK PICTURE - RETRACE LINES AND NO OSD
CHECK/REPLACE IC680 (P/N# 483520987988)

PHILIPS
N/A
27U1
DEAD SET
CHECK/REPLACE Q501 FOR SHORT

PHILIPS
N/A
27U1
INTERMITTENT TUNER AUDIO OR LOW-DISTORTED TUNER AUDIO
CHECK/REPLACE C205 (P/N# 483512287073)

PHILIPS
N/A
27U1
SET SHUTS DOWN
CHECK/REPLACE R465 (P/N# 483511127001)

PHILIPS
N/A
27U1
DARK LINE TO THE LEFT OF THE COLOR PIP IMAGE RUNNING THE HEIGHT OF THE PIP BORDER
CHECK/REPLACE THE PIP MODULE

PHILIPS
N/A
27U1
OSD IS OFF CENTER
ADJUST C341 FOR CORRECT CENTERING OF OSD

PHILIPS
N/A
27U1
DISTORTED AUDIO WITH TEARING IN THE PICTURE
REMOVE C190 - DO NOT INSTALL BR190

PHILIPS
N/A
27U1
LOW OR WEAK CONTRAST
CHECK/REPLACE C511 (P/N# 483512147092)

PHILIPS
N/A
27U1
INTERMITTENT DEGAUSSING
CHECK/REPLACE R402 (P/N# 483511137026)

PHILIPS
N/A
27U1
SET SHUTS DOWN - 130 VOLT SUPPLY IS TOO HIGH
CHECK/REPLACE Z460 (P/N# 483513037068)

PHILIPS
N/A
27U1
DEAD SET AND NO ATTEMPT TO TURN ON
CHECK/REPLACE Q501 FOR SHORT ( REPL. WITH A 2SD1555 )

PHILIPS
N/A
27U1
REPEATED FAILURE OF HORZ. OUTPUT XSTR.
CHECK/REPLACE WITH A (483513047835)

PHILIPS
N/A
27U1
INTERMITTENT SQUEAL IN POWER SUPPLY
CHECK/REPLACE C416 (P/N# 483512287066)

PHILIPS
N/A
27U1
NO VERTICAL SWEEP
CHECK/REPLACE Q304 (P/N# 483513047086)

PHILIPS
N/A
27U1
DISTORTED AUDIO AND TEARING IN THE PICTURE (ONLY AFFECTS THE MODELS WITH THE 2.5 WATT AUDIO AMPLIFIER)
REMOVE C190 (SURFACE MOUNT)

PHILIPS
N/A
27U6
DEAD SET - NO HIGH VOLTAGE
CHECK/REPLACE Q500 (P/N# 483513047073)

PHILIPS
N/A
27V5
NO OSD - SET FUNCTIONS FINE OTHERWISE
CHECK/REPLACE L325 OR OPEN TRACE AT PINS# 18 & 19 OF IC300

PHILIPS
N/A
27V5
INTERMITTENT CLOSED CAPTION OPERATION - DOUBLE SPACED LINES DROPOUTS OR COMPLETE LOSS.
C358 WAS INSTALLED IN REVERSE (P/N# 483512497175)

PHILIPS
N/A
27V5
DEAD SET EXCEPT POWER LED
CHECK/REPLACE R538

PHILIPS
N/A
27V5
NARROW RASTER - LACKING WIDTH
CHECK/REPLACE C512 (P/N# 483512257004) (820pF)

PHILIPS
N/A
27V5
CANNOT DELETE CHANNELS FROM THE 'SMART SURF' ** RECORD ALL SERVICE MODE REGISTERS BEFORE REPL. PARTS **
CHECK/REPLACE IC300 (P/N# 483520988488) AND IC302 (P/N# 483520988326)- RECORD ALL SERVICE SETTINGS 1ST

PHILIPS
N/A
27V5
LOOKS LIKE WEAK CRT - LOW EMISSION - SLOW WARM UP - DIM PICTURE - COLOR BLEEDING - SILVERY HIGHLIGHTS
CHECK/REPLACE R502 WITH NEW VALUE (.62 OR .68) (P/N# 483511667184)

PHILIPS
N/A
27V5
'SCREEN DOOR' EFFECT IN PICTURE DETAIL
CHECK/REPLACE Y600 COMB FILTER (P/N# 483515287002)

PHILIPS
N/A
27V5
HORZ. OFF FREQUENCY - MAY BE INTERMITTENT
CHECK/REPLACE Y620 (P/N# 483524277215)

PHILIPS
N/A
27V5
POOR VERTICAL SYNC.(ROLL,JITTER,BOUNCE) ON PREMIUM CHANNELS
CHANGE C682 TO 0.22uF POLY CAP (P/N# 483512147002) AND ADD 1.2m FROM JUMPER B57 TO B40

PHILIPS
N/A
27V5
VOLUME LOSS W/CHANNEL CHANGE,SAP LOCKUP IN FRENCH MENU, SMART CLOCK OFF 1 HR. ** ONLY ON SETS WITH BLUE MENU BOX **
CHECK/REPLACE MICROPROCESSOR (P/N# 483520988505)

PHILIPS
N/A
27W1
DARK LINE TO THE LEFT OF THE COLOR PIP IMAGE RUNNING THE HEIGHT OF THE PIP BORDER
CHECK/REPLACE THE PIP MODULE

PHILIPS
N/A
27W1
POP IN THE AUDIO AT HIGH VOLUME
CHECK/REPLACE R185 AND R186 (BOTH ARE SMD'S)

PHILIPS
N/A
27W1
INCREASED VERT.HEIGHT AFTER WARM-UP
CHECK/REPLACE C558 ALSO DRESS IT AWAY FROM THE NEAR BY HEATSINK.

PHILIPS
N/A
27W1
NO VERTICAL SWEEP OR REPEATED VERTICAL FAILURES
CHECK/REPLACE IC550 AND R553 (R553 SHOULD BE REPLACED WITH A 2 OHM 1/2 W LEADED TYPE RESISTOR)

PHILIPS
N/A
27W1
VERTICAL JITTER ON SOME CABLE CHANNEL (USUALLY PREMIUM)
CHANGE R267 TO A 27K

PHILIPS
N/A
27W1
TOTAL LOSS OF OSD
INSTALL 4.7k BETWEEN PINS 5&8 OF IC308 - SOLDER RESISTOR TO LEADS OF L307 AND L335.

PHILIPS
N/A
27W5
BRIGHTNESS LEVEL VARIES BETWEEN THE TUNER SIGNAL AND THE VIDEO INP

    • Re: PHILIPSAnonymous, Wed Dec 24 12:04pm
      PHILIPS MS1462C301 13Y4 VERTICAL OUTPUT FAILURE CHECK/REPLACE IC550 AND C447 (P/N# 483512447013) PHILIPS MS1462C301 13Y4 SHORT VERTICAL SWEEP OR FOLDOVER CHECK/REPLACE Q560 (P/N# 483513047064) AND... more
      • PhilipsHarry, Mon Sep 6 11:29am
        Philips 27K241B101 (main chassis EMW153) Customer complaint: Dead-burning smell The TV had no high voltage. C505 a 330pf 2KV capacitor was burnt. C505 (P/N 483512247058)
  • Click here to receive daily updates