Lease this WebApp and get rid of the ads.
Anonymous
Re: TOSHIBA
Tue Jan 13, 2004 7:40pm
216.174.155.86 (XFF: 216.174.155.92)

TOSHIBA
CF907
N/A
LOSS OF VERTICAL DEFLECTION
REPLACE IC301,R327--CHANGE D301--ADD 220uF/35V IC301

TOSHIBA
CF907
N/A
NO COLOR
CHECK/REPLACE R491 FOR OPEN

TOSHIBA
CF907
N/A
NO VERTICAL SWEEP AND VERT. OUT IC MAY BE VERY HOT
CHECK/REPLACE D320 FOR LEAKAGE (P/N# ECG552)

TOSHIBA
CF907
TAC8721
HIGH SHRILL NOISE AT THE END OF A WORD
ADD 2.7k BETWEEN LA03 & RB38-3.3uF TO RES AND RB38

TOSHIBA
CF907
TAC8721
FLAGGING WHEN VIEWING COPY GUARDED VCR TAPES
R403 TO 3.0k,ADD 1ss176FA DIODE ACROSS R406,ANDE R412

TOSHIBA
CF915
N/A
AUDIO BUZZ ON A CATV SYSTEM
ADD 1000pF BET. PIN#34 OF IC501 & R611,2.7k>R611>GRD

TOSHIBA
CF915
N/A
NO RASTER AND NO SOUND
CHECK/REPLACE R416 AND R418

TOSHIBA
CF916
N/A
NO RASTER AND NO SOUND
CHECK/REPLACE R416 AND R418

TOSHIBA
CF916
N/A
NO COLOR
CHECK/REPLACE R491 FOR OPEN

TOSHIBA
CF916
TAC8620
FLAGGING WHEN VIEWING COPY GUARDED VCR TAPES
R403 TO 3.0k,ADD 1ss176FA DIODE ACROSS R320,ANDE R321

TOSHIBA
CF916
TAC8620
AUDIO BUZZ ON A CATV SYSTEM
ADD 1000pF BET. PIN#34 OF IC501 & R611,2.7k>R611>GRD

TOSHIBA
CF917
N/A
NO COLOR
CHECK/REPLACE R491 FOR OPEN

TOSHIBA
CF917
TAC8720
FLAGGING WHEN VIEWING COPY GUARDED VCR TAPES
R403 TO 3.0k,ADD 1ss176FA DIODE ACROSS R406,ANDE R412

TOSHIBA
CF917
TAC8720
HIGH SHRILL NOISE AT THE END OF A WORD
ADD 2.7k BETWEEN LA03 & RB38-3.3uF TO RES AND RB38

TOSHIBA
CF917
TAC8720
UNUSUAL ODOR COMING FROM SET
REPLACE YOKE WITH A REVISED REPLACEMENT

TOSHIBA
CF917
TAC8720
SNOW NOISE,WAVY LINES THRU PIX,AUDIO HISS
REPLACE IC501 WITH NEW VERSION (B0383100)

TOSHIBA
CF917
TAC8720
SHORT VERT. SWEEP--IC301 OK
CHECK R327 AND D302

TOSHIBA
CH20D02
N/A
WHILE SET IS OFF AND POWER IS INTERUPTED, THE SET TURNS ON BY ITSELF WHEN POWER IS RESTORED
CHECK/REPLACE ICA01 (P/N# 23904906) AND ADD A 10kę RESISTOR BETWEEN PIN #1 AND PIN #6 OF ICA02

TOSHIBA
CL14E26
N/A
NOT TUNING ALL STATIONS OR NOT TUNING AT ALL
CHECK/REPLACE G001 (P/N# 23316694) 33v ZENER AND/OR TUNER (P/N# 23321147)

TOSHIBA
CL21E46
N/A
THE LETTERS 'EDS' MAY NOT APPEAR ON SCREEN WHILE RECEIVING THE EXTENDED SERVICE DATA
CHECK/REPLACE ICA01 (P/N# 23905641)

TOSHIBA
CL21E46
N/A
PICTURE DISCOLORATION
R808 MAY BE IN WRONG PLACE -- IT SHOULD BE CONNECTED TO M801B(WHT) TO CONNECTOR P910, PIN #3

TOSHIBA
CL21E46
N5ES
DEAD SET - RELAY CLICKS CHECK/REPLACE Q801 (23905513), F860 (23144511),
C866 (24669010), D872 (23316302), D873 (23316327), D875 (23316333), D876 (23316359)

TOSHIBA
CL21E46
N5ES
LOW B+ AND POOR PINCUSHION ON EACH SIDE
CHECK/REPLACE C884 (P/N# 24640018) 220uF @ 160v

TOSHIBA
CL21F40
N5ES
DEAD SET - RELAY CLICKS CHECK/REPLACE Q801 (23905513), F860 (23144511),
C866 (24669010), D872 (23316302), D873 (23316327), D875 (23316333), D876 (23316359)

TOSHIBA
CL21F40
N5ES
LOW B+ AND POOR PINCUSHION ON EACH SIDE
CHECK/REPLACE C884 (P/N# 24640018) 220uF @ 160v

TOSHIBA
CL29E36
N/A
THE LETTERS 'EDS' MAY NOT APPEAR ON SCREEN WHILE RECEIVING THE EXTENDED SERVICE DATA
CHECK/REPLACE ICA01 (P/N# 23905641)

TOSHIBA
CL29E36
N5ES
LOW B+ AND POOR PINCUSHION ON EACH SIDE
CHECK/REPLACE C884 (P/N# 24640018) 220uF @ 160v

TOSHIBA
CL29E36
N5ES
DEAD SET - RELAY CLICKS CHECK/REPLACE Q801 (23905513), F860 (23144511),
C866 (24669010), D872 (23316302), D873 (23316327), D875 (23316333), D876 (23316359)

TOSHIBA
CL29F30
N5ES
DEAD SET - RELAY CLICKS CHECK/REPLACE Q801 (23905513), F860 (23144511),
C866 (24669010), D872 (23316302), D873 (23316327), D875 (23316333), D876 (23316359)

TOSHIBA
CL29F30
N5ES
LOW B+ AND POOR PINCUSHION ON EACH SIDE
CHECK/REPLACE C884 (P/N# 24640018) 220uF @ 160v

TOSHIBA
CL29F50
N/A
WHITE DOT NOISE IN THE PIP VIDEO
CHANGE DY10 FROM 3.9v ZENER TO A 4.3v ZENER - ANY OF THESE (P/N# 23316298 OR 23316662 OR 23118626 OR A7116105)

TOSHIBA
CL29F50
N5ES
DEAD SET - RELAY CLICKS CHECK/REPLACE Q801 (23905513), F860 (23144511),
C866 (24669010), D872 (23316302), D873 (23316327), D875 (23316333), D876 (23316359)

TOSHIBA
CL29F50
N5ES
LOW B+ AND POOR PINCUSHION ON EACH SIDE
CHECK/REPLACE C884 (P/N# 24640018) 220uF @ 160v

TOSHIBA
CL32E56
N/A
INTERFERENCE NOISE AND PIP GHOSTING IN THE MAIN PICTURE WITH PIP ON OR OFF
ADD C116 (24212391) 390pF BETWEEN AGC PIN ON TUNER TO GRD. REMOVE JP062, ADD JUMPER FROM 'YF' TO TUNER GROUND

TOSHIBA
CL32F40
N5ES
DEAD SET - RELAY CLICKS CHECK/REPLACE Q801 (23905513), F860 (23144511),
C866 (24669010), D872 (23316302), D873 (23316327), D875 (23316333), D876 (23316359)

TOSHIBA
CL32F40
N5ES
LOW B+ AND POOR PINCUSHION ON EACH SIDE
CHECK/REPLACE C884 (P/N# 24640018) 220uF @ 160v

TOSHIBA
CL34E56
N/A
INTERFERENCE NOISE AND PIP GHOSTING IN THE MAIN PICTURE WITH PIP ON OR OFF
ADD C116 (24212391) 390pF BETWEEN AGC PIN ON TUNER TO GRD. REMOVE JP062, ADD JUMPER FROM 'YF' TO TUNER GROUND

TOSHIBA
CL34F40
N/A
DEAD SET
CHECK/REPLACE F801 (P/N# 23144735 5A GMA) AND Q610 (P/N# B0377324 TA8246H)

TOSHIBA
CL34F40
N5ES
DEAD SET - RELAY CLICKS CHECK/REPLACE Q801 (23905513), F860 (23144511),
C866 (24669010), D872 (23316302), D873 (23316327), D875 (23316333), D876 (23316359)

TOSHIBA
CL34F40
N5ES
LOW B+ AND POOR PINCUSHION ON EACH SIDE
CHECK/REPLACE C884 (P/N# 24640018) 220uF @ 160v

TOSHIBA
CL37E56
N/A
CHANNELS WITHOUT A SIGNAL ARE BEING PROGRAMMMED DURING AUTO-PROGRAMMING
CHECK/REPLACE CA13 AND CA36 WITH 220pF (P/N# 24474221)

TOSHIBA
CL37E56
N/A
WHEN SWAPPING PIP WITH MAIN AND THEN BACK, THE RIGHT MOST CHARACTER OF THE CHANNEL CAPTION MAY BE GONE OR WRONG CHAR.
CHECK/REPLACE ICA01 (P/N# 23905550)

TOSHIBA
CL37E56
N/A
DEAD SET
CHECK/REPLACE F899 (P/N# 23144735 5A GMA) AND Q670 (P/N# B0377324 TA8246H)

TOSHIBA
CL37E56
N/A
INTERMITTENT SHUTDOWN - SET SHUTS OFF THEN COMES BACK ON WHEN PRESSING AND HOLDING THE NUMBER BUTTONS ON REMOTE
CHECK/REPLACE ICA01 (P/N# 23905550)

TOSHIBA
CL37E56
N5ES
DEAD SET - RELAY CLICKS CHECK/REPLACE Q801 (23905513), F860 (23144511),
C866 (24669010), D872 (23316302), D873 (23316327), D875 (23316333), D876 (23316359)

TOSHIBA
CL37E56
N5ES
LOW B+ AND POOR PINCUSHION ON EACH SIDE
CHECK/REPLACE C884 (P/N# 24640018) 220uF @ 160v

TOSHIBA
CN2781
N/A
POOR VERTICAL LINEARITY
CHECK/REPLACE C308 (P/N# 24668221) 220 F @ 35v HI-TEMP

TOSHIBA
CN27C90
N/A
POOR VERTICAL LINEARITY
CHECK/REPLACE C308 (P/N# 24668221) 220 F @ 35v HI-TEMP

TOSHIBA
CN27C90
N/A
PIP PICTURE JITTERS VERTICALLY
ADD A 1.5 meg BETWEEN PINS#24 AND #25 OF ICY01 OF PIP BD.

TOSHIBA
CN27D90
N/A
JUMBLED LETTERS OR UPSIDE DOWN 'T' IN CHANNEL CAPTIONS
CHECK/REPLACE ICA01 (P/N# 23904802)

TOSHIBA
CN27D90
N/A
VERTICAL JITTER
CHECK/REPLACE D361,Q361,C364 AND C365

TOSHIBA
CN27E90
N/A
WHEN SWAPPING PIP WITH MAIN AND THEN BACK, THE RIGHT MOST CHARACTER OF THE CHANNEL CAPTION MAY BE GONE OR WRONG CHAR.
CHECK/REPLACE ICA01 (P/N# 23905549)

TOSHIBA
CN3081
N/A
POOR VERTICAL LINEARITY
CHECK/REPLACE C308 (P/N# 24668221) 220 F @ 35v HI-TEMP

TOSHIBA
CN3081B
N/A
BUZZING NOISE FROM SPEAKER SWITCH WITH SPEAKER SWITCH IN THE OFF MODE
ADD A JUMPER BETWEEN THE NEGATIVE SIDE OF C641 AND THE NEGATIVE SIDE OF C637

TOSHIBA
CN30C90
N/A
POOR VERTICAL LINEARITY
CHECK/REPLACE C308 (P/N# 24668221) 220 F @ 35v HI-TEMP

TOSHIBA
CN32C90
N/A
INTERMITTENTLY GOES TO GREEN SCREEN LIKE A SHORTED CRT P/N# A7150258 = 6.2v ZENER AND P/N# A7116515 = 1SS176
ADD A 6.2v ZENER (ANODE-PIN 41,IC501 AND CATH.TO CATH D204) ADD 1SS176 (ANODE-PIN 18 C/C BOARD & CATH.-PIN 15 C/C BD.)

TOSHIBA
CN32C90
N/A
PIP PICTURE JITTERS VERTICALLY
ADD A 1.5 meg BETWEEN PINS#24 AND #25 OF ICY01 OF PIP BD.

TOSHIBA
CN32D90
N/A
VOLUME AND CHANNEL BUTTON FUNCTIONS ARE REVERSED ** TURN SET ON, PRESS MUTE BUTTON ONCE, THEN PRESS MUTE
AGAIN AND HOLD WHILE PRESSING MENU BUTTON ON TV, PRESS MENU TO ADVANCE TO 'ADD DATA 174',PRESS +/- ON REMOTE TO SET #20

TOSHIBA
CN32E90
N/A
CHANNELS WITHOUT A SIGNAL ARE BEING PROGRAMMMED DURING AUTO-PROGRAMMING
CHECK/REPLACE CA13 AND CA36 WITH 220pF (P/N# 24474221)

TOSHIBA
CN32E90
N/A
WHEN SWAPPING PIP WITH MAIN AND THEN BACK, THE RIGHT MOST CHARACTER OF THE CHANNEL CAPTION MAY BE GONE OR WRONG CHAR.
CHECK/REPLACE ICA01 (P/N# 23905549)

TOSHIBA
CN35C90
N/A
PIP PICTURE JITTERS VERTICALLY
ADD A 1.5 meg BETWEEN PINS#24 AND #25 OF ICY01 OF PIP BD.

TOSHIBA
CN35C90
N/A
PINCUSHION PROBLEMS ON LEFT SIDE OF SCREEN
CHECK/REPLACE MODIFICATION KIT (P/N# 23305500)

TOSHIBA
CN35D90
N/A
VOLUME AND CHANNEL BUTTON FUNCTIONS ARE REVERSED ** TURN SET ON, PRESS MUTE BUTTON ONCE, THEN PRESS MUTE
AGAIN AND HOLD WHILE PRESSING MENU BUTTON ON TV, PRESS MENU TO ADVANCE TO 'ADD DATA 174',PRESS +/- ON REMOTE TO SET #00


  • Re: TOSHIBAAnonymous, Tue Jan 13 7:38pm
    TOSHIBA CF30C50 N/A NO COLOR - GOOD BLACK AND WHITE PICTURE CHECK/REPLACE C260 FOR LEAKAGE OR SHORT (0.01uF @ 100v) TOSHIBA CF30C50 N/A MISSING A PRIMARY COLOR - RED,BLUE OR GREEN CHECK/REPLACE OPEN... more
    • Re: TOSHIBA — Anonymous, Tue Jan 13 7:40pm
      • Re: TOSHIBAAnonymous, Tue Jan 13 7:41pm
        TOSHIBA CN35E90 N/A CHANNELS WITHOUT A SIGNAL ARE BEING PROGRAMMMED DURING AUTO-PROGRAMMING CHECK/REPLACE CA13 AND CA36 WITH 220pF (P/N# 24474221) TOSHIBA CN35E90 N/A WHEN SWAPPING PIP WITH MAIN AND... more
        • Re: TOSHIBAAnonymous, Tue Jan 13 7:44pm
          TOSHIBA CX2785B N/A BUZZING NOISE FROM SPEAKER SWITCH WITH SPEAKER SWITCH IN THE OFF MODE ADD A JUMPER BETWEEN THE NEGATIVE SIDE OF C641 AND THE NEGATIVE SIDE OF C637 TOSHIBA CX2786 N/A POOR VERTICAL ... more
          • Re: TOSHIBAAnonymous, Tue Jan 13 7:48pm
            TOSHIBA CX32E70 N/A CHANNELS WITHOUT A SIGNAL ARE BEING PROGRAMMMED DURING AUTO-PROGRAMMING CHECK/REPLACE CA13 AND CA36 WITH 220pF (P/N# 24474221) TOSHIBA CX32E70 N/A DEAD SET CHECK/REPLACE F899... more
            • remote sensormary, Thu Apr 8 3:05pm
              remote sensor appears to not be working. We cannot get it to respond to any universal remotes and no longer have the original remote. Is is possible that the sensor needs replacing. Any suggestions.... more
            • C227T31Jay, Fri Jul 3 7:35pm
              Remote control no longer turns TV on/off and does not change channels - everything else on remote control works - batteries have been changed several times Can anyone tell me what the problem is and... more
            • Re: TOSHIBAAnonymous, Tue Jan 13 7:57pm
              Toshiba 27h50 horizontal out blowed (many times) check & change ac 110v power plug and add 470 uf from base of 12v reg to gnd Comments:bad contact on ac plug generate supply peaks that deteriorates... more
              • CX32C81Anonymous, Mon Oct 27 10:44am
                no sound, No picture green line goes straight across the middle of the tv
                • Re: CX32C81Anonymous, Tue Oct 28 9:46am
                  Sounds like no vertical sweep. Check vertical ic and it blown side of ic must check for open resistor and shorted diode feeding dc to vertical. Now also would check qf03 9v regulator for poor... more
              • ToshibaAnonymous, Mon Sep 6 11:37am
                Toshiba CE32T11 Customer Complaint: Dead set The TV was dead except that the power LED was on. After checking the standby power and finding it to be ok, I found that there was no drive to the power... more
Click here to receive daily updates