Lease this WebApp and get rid of the ads.
Anonymous
Re: TOSHIBA
Tue Jan 13, 2004 7:48pm
216.174.155.87 (XFF: 216.174.155.92)

TOSHIBA
CX32E70
N/A
CHANNELS WITHOUT A SIGNAL ARE BEING PROGRAMMMED DURING AUTO-PROGRAMMING
CHECK/REPLACE CA13 AND CA36 WITH 220pF (P/N# 24474221)

TOSHIBA
CX32E70
N/A
DEAD SET
CHECK/REPLACE F899 (P/N# 23144735 5A GMA) AND Q670 (P/N# B0377324 TA8246H)

TOSHIBA
CX32E70
N/A
WHEN SWAPPING PIP WITH MAIN AND THEN BACK, THE RIGHT MOST CHARACTER OF THE CHANNEL CAPTION MAY BE GONE OR WRONG CHAR.
CHECK/REPLACE ICA01 (P/N# 23905549)

TOSHIBA
CX32F60
N/A
CHANNELS WITHOUT A SIGNAL ARE BEING PROGRAMMMED DURING AUTO-PROGRAMMING
CHECK/REPLACE CA12 AND CA36 WITH 220pF (P/N# 24474221)

TOSHIBA
CX32F60
N/A
DEAD SET
CHECK/REPLACE F801 (P/N# 23144735 5A GMA) AND Q610 (P/N# B0377324 TA8246H)

TOSHIBA
CX32F60
N5S
DEAD SET
CHECK/REPLACE IC801 (P/N# 23904984), D876 (P/N# 23316360), F860 (P/N# 23144773)

TOSHIBA
CX34640
N/A
NO SOUND
CHECK/REPLACE IC601 (TA8218AH P/N# B0377305),D601,D602, D603,D604,D605,D606,F803

TOSHIBA
CX34640
N/A
SET BEGINS TO COME ON THEN IMMEDIATELY SHUTS DOWN - SOUNDS LIKE TUBE OR YOKE IS ARCING
CHECK/REPLACE DEFLECTION YOKE FOR SHORTED HORZ. WINDING (P/N# 23227392)

TOSHIBA
CX34662
N/A
DEAD SET
CHECK/REPLACE F803 (5A PICA FUSE) IN 22VOLT SUPPLY

TOSHIBA
CX34723
N/A
DEAD SET - NO RELAY CLICK - JUMPERING RELAY ALLOWS HIGH VOLTAGE TO COME UP
CHECK/REPLACE Q840 (P/N# 23318299)

TOSHIBA
CX3583
N/A
PIP PICTURE IS UNSTABLE VERTICALLY
REMOVE RY09 AND REPLACE WITH A 10k 1/4 watt

TOSHIBA
CX3583A
N/A
UNSTABLE PIP PICTURE VERTICALLY OR PIP JITTERS
REMOVE RY09 AND REPLACE WITH A 10k ohm

TOSHIBA
CX3586
N/A
DEAD SET - NO ATTEMPT TO TURN ON
CHECK/REPLACE Q862 (P/N# A6317440), Q845 (P/N# A6907752), Q841 (P/N# A8643135), IC801 (P/N# 23319619)

TOSHIBA
CX3586
N/A
PIP PICTURE IS UNSTABLE VERTICALLY
REMOVE RY09 AND REPLACE WITH A 10k 1/4 watt

TOSHIBA
CX3586A
N/A
PICTURE FOLDS OVER AT THE TOP AFTER REPLACEMENT OF THE VERTICAL OUTPUT IC Q301
CHANGE R301 TO A JUMPER OR SHORT ACROSS RESISTOR

TOSHIBA
CX3586A
N/A
UNSTABLE PIP PICTURE VERTICALLY OR PIP JITTERS
REMOVE RY09 AND REPLACE WITH A 10k ohm

TOSHIBA
CX3586A
N/A
FOLDOVER AT TOP OF PICTURE AFTER IC Q301 IS REPLACED
SHORT R301 OUT WITH A JUMPER

TOSHIBA
CX35C60
N/A
INTERMITTENTLY GOES TO GREEN SCREEN LIKE A SHORTED CRT P/N# A7150258 = 6.2v ZENER AND P/N# A7116515 = 1SS176
ADD A 6.2v ZENER (ANODE-PIN 41,IC501 AND CATH.TO CATH D204) ADD 1SS176 (ANODE-PIN 18 C/C BOARD & CATH.-PIN 15 C/C BD.)

TOSHIBA
CX35C60
N/A
PIP PICTURE JITTERS VERTICALLY
ADD A 1.5 meg BETWEEN PINS#24 AND #25 OF ICY01 OF PIP BD.

TOSHIBA
CX35C60
N/A
PINCUSHION PROBLEMS ON LEFT SIDE OF SCREEN
CHECK/REPLACE MODIFICATION KIT (P/N# 23305500)

TOSHIBA
CX35C80
N/A
INTERMITTENTLY GOES TO GREEN SCREEN LIKE A SHORTED CRT P/N# A7150258 = 6.2v ZENER AND P/N# A7116515 = 1SS176
ADD A 6.2v ZENER (ANODE-PIN 41,IC501 AND CATH.TO CATH D204) ADD 1SS176 (ANODE-PIN 18 C/C BOARD & CATH.-PIN 15 C/C BD.)

TOSHIBA
CX35C81
N/A
INTERMITTENTLY GOES TO GREEN SCREEN LIKE A SHORTED CRT P/N# A7150258 = 6.2v ZENER AND P/N# A7116515 = 1SS176
ADD A 6.2v ZENER (ANODE-PIN 41,IC501 AND CATH.TO CATH D204) ADD 1SS176 (ANODE-PIN 18 C/C BOARD & CATH.-PIN 15 C/C BD.)

TOSHIBA
CX35C81
N/A
NO HORZ. SWEEP
CHECK/RESOLDER CONNECTIONS ON YOKE PLUG - CHECK FOR A BROKEN CRIMP CONNECTOR, ESPECIALLY BLUE AND RED WIRES

TOSHIBA
CX35D60
N/A
VOLUME AND CHANNEL BUTTON FUNCTIONS ARE REVERSED ** TURN SET ON, PRESS MUTE BUTTON ONCE, THEN PRESS MUTE
AGAIN AND HOLD WHILE PRESSING MENU BUTTON ON TV, PRESS MENU TO ADVANCE TO 'ADD DATA 174',PRESS +/- ON REMOTE TO SET #11

TOSHIBA
CX35D70
N/A
VOLUME AND CHANNEL BUTTON FUNCTIONS ARE REVERSED ** TURN SET ON, PRESS MUTE BUTTON ONCE, THEN PRESS MUTE
AGAIN AND HOLD WHILE PRESSING MENU BUTTON ON TV, PRESS MENU TO ADVANCE TO 'ADD DATA 174',PRESS +/- ON REMOTE TO SET #10

TOSHIBA
CX35D80
N/A
VOLUME AND CHANNEL BUTTON FUNCTIONS ARE REVERSED ** TURN SET ON, PRESS MUTE BUTTON ONCE, THEN PRESS MUTE
AGAIN AND HOLD WHILE PRESSING MENU BUTTON ON TV, PRESS MENU TO ADVANCE TO 'ADD DATA 174',PRESS +/- ON REMOTE TO SET #11

TOSHIBA
CX35D81
N/A
VOLUME AND CHANNEL BUTTON FUNCTIONS ARE REVERSED ** TURN SET ON, PRESS MUTE BUTTON ONCE, THEN PRESS MUTE
AGAIN AND HOLD WHILE PRESSING MENU BUTTON ON TV, PRESS MENU TO ADVANCE TO 'ADD DATA 174',PRESS +/- ON REMOTE TO SET #11

TOSHIBA
CX35E60
N/A
CHANNELS WITHOUT A SIGNAL ARE BEING PROGRAMMMED DURING AUTO-PROGRAMMING
CHECK/REPLACE CA13 AND CA36 WITH 220pF (P/N# 24474221)

TOSHIBA
CX35E60
N/A
WHEN SWAPPING PIP WITH MAIN AND THEN BACK, THE RIGHT MOST CHARACTER OF THE CHANNEL CAPTION MAY BE GONE OR WRONG CHAR.
CHECK/REPLACE ICA01 (P/N# 23905549)

TOSHIBA
CX35E60
N/A
DEAD SET
CHECK/REPLACE F899 (P/N# 23144735 5A GMA) AND Q670 (P/N# B0377324 TA8246H)

TOSHIBA
CX35E70
N/A
DEAD SET
CHECK/REPLACE F899 (P/N# 23144735 5A GMA) AND Q670 (P/N# B0377324 TA8246H)

TOSHIBA
CX35E70
N/A
DEAD SET
CHECK/REPLACE F899 (P/N# 23144735 5A GMA) AND Q670 (P/N# B0377324 TA8246H)

TOSHIBA
CX35E70
N/A
CHANNELS WITHOUT A SIGNAL ARE BEING PROGRAMMMED DURING AUTO-PROGRAMMING
CHECK/REPLACE CA13 AND CA36 WITH 220pF (P/N# 24474221)

TOSHIBA
CX35E70
N/A
WHEN SWAPPING PIP WITH MAIN AND THEN BACK, THE RIGHT MOST CHARACTER OF THE CHANNEL CAPTION MAY BE GONE OR WRONG CHAR.
CHECK/REPLACE ICA01 (P/N# 23905549)

TOSHIBA
CX35E80
N/A
CHANNELS WITHOUT A SIGNAL ARE BEING PROGRAMMMED DURING AUTO-PROGRAMMING
CHECK/REPLACE CA13 AND CA36 WITH 220pF (P/N# 24474221)

TOSHIBA
CX35E81
N/A
DEAD SET
CHECK/REPLACE F899 (P/N# 23144735 5A GMA) AND Q670 (P/N# B0377324 TA8246H)

TOSHIBA
CX35E81
N/A
WHEN SWAPPING PIP WITH MAIN AND THEN BACK, THE RIGHT MOST CHARACTER OF THE CHANNEL CAPTION MAY BE GONE OR WRONG CHAR.
CHECK/REPLACE ICA01 (P/N# 23905549)

TOSHIBA
CX35E95
N/A
DEAD SET
CHECK/REPLACE F899 (P/N# 23144735 5A GMA) AND Q670 (P/N# B0377324 TA8246H)

TOSHIBA
CX35F60
N/A
DEAD SET
CHECK/REPLACE F801 (P/N# 23144735 5A GMA) AND Q610 (P/N# B0377324 TA8246H)

TOSHIBA
CX35F60
N/A
CHANNELS WITHOUT A SIGNAL ARE BEING PROGRAMMMED DURING AUTO-PROGRAMMING
CHECK/REPLACE CA12 AND CA36 WITH 220pF (P/N# 24474221)

TOSHIBA
CX35F60
N5S
DEAD SET
CHECK/REPLACE IC801 (P/N# 23904984), D876 (P/N# 23316360), F860 (P/N# 23144773)

TOSHIBA
CX35F67
N/A
HORZ. NOISE LINES THROUGH THE PICTURE WHICH INCREASES OR DECREASES WITH VOL. - DISTORTED OR NO SOUND
REDRESS THE SPEAKER LEADS TOWARDS THE FRONT OF CRT

TOSHIBA
CX35F70
N/A
DEAD SET
CHECK/REPLACE F899 (P/N# 23144735 5A GMA) AND Q670 (P/N# B0377324 TA8246H)

TOSHIBA
CX35F82
N/A
CHANNELS WITHOUT A SIGNAL ARE BEING PROGRAMMMED DURING AUTO-PROGRAMMING
CHECK/REPLACE CA12 AND CA36 WITH 220pF (P/N# 24474221)

TOSHIBA
CX35F83
N/A
CHANNELS WITHOUT A SIGNAL ARE BEING PROGRAMMMED DURING AUTO-PROGRAMMING
CHECK/REPLACE CA12 AND CA36 WITH 220pF (P/N# 24474221)

TOSHIBA
CX35F85
N/A
HORZ. NOISE LINES THROUGH THE PICTURE WHICH INCREASES OR DECREASES WITH VOL. - DISTORTED OR NO SOUND
REDRESS THE SPEAKER LEADS TOWARDS THE FRONT OF CRT

TOSHIBA
CX36F67
N/A
CHANNELS WITHOUT A SIGNAL ARE BEING PROGRAMMMED DURING AUTO-PROGRAMMING
CHECK/REPLACE CA12 AND CA36 WITH 220pF (P/N# 24474221)

TOSHIBA
CX36F84
N/A
CHANNELS WITHOUT A SIGNAL ARE BEING PROGRAMMMED DURING AUTO-PROGRAMMING
CHECK/REPLACE CA12 AND CA36 WITH 220pF (P/N# 24474221)

TOSHIBA
CX36F85
N/A
CHANNELS WITHOUT A SIGNAL ARE BEING PROGRAMMMED DURING AUTO-PROGRAMMING
CHECK/REPLACE CA12 AND CA36 WITH 220pF (P/N# 24474221)

TOSHIBA
CX37662
N/A
DEAD SET - RELAY WILL NOT CLICK
CHECK/REPLACE ICA01 (23319163) AND DA44 (A7116515)

TOSHIBA
CX37662
N/A
MAIN VIDEO MISSING BUT DOES HAVE CHROMA - ALSO PIP VIDEO IS FINE
CHECK/REPLACE IC501 AND Q205

TOSHIBA
CX37662
N/A
NO PIP OPERATION - BOX WILL NOT COME UP ON SCREEN BUT THE SWAP FEATURE DOES WORK OK
CHECK/REPLACE IC840 (POWER SUPPLY BOARD)

TOSHIBA
CX37662
N/A
DEAD SET - NO ATTEMPT TO TURN ON
CHECK/REPLACE Q862 (P/N# A6317440), Q845 (P/N# A6907752), Q841 (P/N# A8643135), IC801 (P/N# 23319619)

TOSHIBA
CX37662
N/A
DEAD SET - RELAY WILL NOT CLICK PIN #44 (RESET) IS BEING DROPPED DOWN TO 1.8v
CHECK/REPLACE IC840 (P/N# 23318299)

TOSHIBA
CX466
N/A
HORZ. PHASE OFF - NO COLOR AND HORZ. BLANKING BAR IS IN THE CENTER OF THE SCREEN
CHECK/REPLACE R402 FOR OPEN (27k)

TOSHIBA
CX467
N/A
HORZ. PHASE OFF - NO COLOR AND HORZ. BLANKING BAR IS IN THE CENTER OF THE SCREEN
CHECK/REPLACE R402 FOR OPEN (27k)

TOSHIBA
CZ2685
N/A
RAINBOW STRIPES ON A DARK SCENE
R919>20k,R927>22k,R921>24k,R208>1.6k,ADD 330k TO C504

TOSHIBA
CZ2695
N/A
RAINBOW STRIPES ON A DARK SCENE
R919>20k,R927>22k,R921>24k,R208>1.6k,ADD 330k TO C504

TOSHIBA
CZ2696
TAC8640
RAINBOW STRIPES ON A DARK SCENE
R919>20k,R927>22k,R921>24k,R208>1.6k,ADD 330k TO C504

TOSHIBA
CZ9700
N/A
AUDIO BUZZ WHEN LETTERS ARE DISPLAYED
CHNG C109 TO 47pF

TOSHIBA
TP4688
N/A
DEAD SET-NO POWER
CHECK D820,D821,C820---ADD VARISTOR PARALLEL TO C801

TOSHIBA
TP4688
N/A
NO POWER CAUSED BY DEFECTIVE Q415
REPLACE Q415 AND ADD 1SS176 DIODE WITH ANODE ON EMIT.

TOSHIBA
TP4688
N/A
AUDIO IS INTERMITTENT OR ONLY CERTAIN CHANNELS HAVE AUDIO
CHECK/REPLACE QB80 FOR LEAKAGE OR R448 FOR A CHANGED VALUE

TOSHIBA
TP4688
N/A
POOR OR NO AFT LOCK
CHECK/ADJUST L171 (AFT COIL) FOR PROPER OPERATION

TOSHIBA
TP4688
N/A
WILL NOT TUNE A CERTAIN BAND OF CHANNELS SUCH AS NO 2-6 OR NO 7-13
CHECK/REPLACE QA63 AND QA64

TOSHIBA
TP4688
N/A
INTERMITTENT AUDIO ON CERTAIN CHANNELS
CHECK QB80 FOR LEAKAGE AND R448 FOR INCREASE

TOSHIBA
TP4688
N/A
INTERMITTENT AUDIO AND MAY BE ONLY ON CERTAIN CHANNELS
CHECK/REPLACE QB80 AND R448

TOSHIBA
TP4688
TAC8890
DEAD SET-SHORT 'D&E',AUDIO COMES UP-NO PIX
Q415--CHECK BOTH HORZ. CIRCUITS FOR OPERATION

TOSHIBA
TP4880
N/A
PIP PICTURE IS UNSTABLE VERTICALLY
REMOVE RY09,RY14 AND REPLACE EACH WITH A 10k 1/4 watt

TOSHIBA
TP4881
N/A
PIP PICTURE IS UNSTABLE VERTICALLY
REMOVE RY09,RY14 AND REPLACE EACH WITH A 10k 1/4 watt

TOSHIBA
TP5288
N/A
DEAD SET-NO POWER
CHECK D820,D821,C820---ADD VARISTOR PARALLEL TO C801

TOSHIBA
TP5288
N/A
NO POWER CAUSED BY DEFECTIVE Q415
REPLACE Q415 AND ADD 1SS176 DIODE WITH ANODE ON EMIT.

TOSHIBA
TP5288
N/A
POOR OR NO AFT LOCK
CHECK/ADJUST L171 (AFT COIL) FOR PROPER OPERATION

TOSHIBA
TP5580
N/A
PIP PICTURE IS UNSTABLE VERTICALLY
REMOVE RY09,RY14 AND REPLACE EACH WITH A 10k 1/4 watt

TOSHIBA
TP5581
N/A
PIP PICTURE IS UNSTABLE VERTICALLY
REMOVE RY09,RY14 AND REPLACE EACH WITH A 10k 1/4 watt

TOSHIBA
TV20D30
N/A
OSD IS SHIFTED TO LEFT OR RIGHT TOO FAR AFTER REPL. ICA02 **TURN SET ON, PRESS MUTE ONCE, PRESS AND HOLD MUTE AGAIN
WHILE PRESSING MENU ON TV,PRESS MENU UNTIL '1E2H' APPEARS, USE +/- UNTIL BLACK BOXES IN UPPER LEFT/LOWER RIGHT CENTER

TOSHIBA
TV28C30
N/A
POPPING NOISE WHEN SET IS TURNED ON OR OFF
CONNECT A LEAD FROM CRT BOARD GROUND TO SPEAKER FRAME AND THEN CONNECT EACH SPEAKER FRAME TOGETHER

TOSHIBA
TV29C35
N/A
INTERMITTENTLY GOES TO GREEN SCREEN LIKE A SHORTED CRT
ADD A 6.2v ZENER (ANODE-PIN 41,IC501 AND CATH.TO CATH D204) ADD 1SS176 (ANODE-PIN 18 C/C BOARD & CATH.-PIN 15 C/C BD.)

TOSHIBA
TV30D50
N/A
WASHED OUT VIDEO - WHEN CHANGING CHANNELS,SCREEN GOES GREEN PIP WORKS BUT UNABLE TO SWAP PIP WITH MAIN PICTURE
CHECK/REPLACE ZY01 PIP MODULE (P/N# 23148210)

TOSHIBA
TV30D50
N/A
NO MAIN PICTURE VIDEO - PIP DOES WORK - WHEN TRYING TO CHANGE CHANNELS, SCREEN GOES ALL GREEN
CHECK/REPLACE ICA01 (P/N# 23904744)

TOSHIBA
TV32C40
N/A
MISSING A PRIMARY COLOR - RED,BLUE OR GREEN
CHECK/REPLACE OPEN L905,L906 OR L907 (P/N# 23237981)

TOSHIBA
TV32C50
N/A
NO COLOR - GOOD BLACK AND WHITE PICTURE
CHECK/REPLACE C260 FOR LEAKAGE OR SHORT (0.01uF @ 100v)

TOSHIBA
TV32C50
N/A
MISSING A PRIMARY COLOR - RED,BLUE OR GREEN
CHECK/REPLACE OPEN L905,L906 OR L907 (P/N# 23237981)

TOSHIBA
TV32D70
N/A
VOLUME AND CHANNEL BUTTON FUNCTIONS ARE REVERSED ** TURN SET ON, PRESS MUTE BUTTON ONCE, THEN PRESS MUTE
AGAIN AND HOLD WHILE PRESSING MENU BUTTON ON TV, PRESS MENU TO ADVANCE TO 'ADD DATA 174',PRESS +/- ON REMOTE TO SET #30

TOSHIBA
TV32D90
N/A
VOLUME AND CHANNEL BUTTON FUNCTIONS ARE REVERSED ** TURN SET ON, PRESS MUTE BUTTON ONCE, THEN PRESS MUTE
AGAIN AND HOLD WHILE PRESSING MENU BUTTON ON TV, PRESS MENU TO ADVANCE TO 'ADD DATA 174',PRESS +/- ON REMOTE TO SET #20

TOSHIBA
TV34C50
N/A
DISTORTED AUDIO IN BOTH CHANNELS
CHECK/REPLACE H004 MTS MODULE (P/N# 23148176)

TOSHIBA
TV35D50
N/A
VOLUME AND CHANNEL BUTTON FUNCTIONS ARE REVERSED ** TURN SET ON, PRESS MUTE BUTTON ONCE, THEN PRESS MUTE
AGAIN AND HOLD WHILE PRESSING MENU BUTTON ON TV, PRESS MENU TO ADVANCE TO 'ADD DATA 174',PRESS +/- ON REMOTE TO SET #11

TOSHIBA
TV35D50
N/A
NO VERTICAL - NO SOUND - BLACK RASTER - DOES HAVE H.V.
CHECK/RESOLDER CONNECTIONS ON D884

TOSHIBA
TV35D70
N/A
VOLUME AND CHANNEL BUTTON FUNCTIONS ARE REVERSED ** TURN SET ON, PRESS MUTE BUTTON ONCE, THEN PRESS MUTE
AGAIN AND HOLD WHILE PRESSING MENU BUTTON ON TV, PRESS MENU TO ADVANCE TO 'ADD DATA 174',PRESS +/- ON REMOTE TO SET #10

TOSHIBA
TV35D90
N/A
VOLUME AND CHANNEL BUTTON FUNCTIONS ARE REVERSED ** TURN SET ON, PRESS MUTE BUTTON ONCE, THEN PRESS MUTE
AGAIN AND HOLD WHILE PRESSING MENU BUTTON ON TV, PRESS MENU TO ADVANCE TO 'ADD DATA 174',PRESS +/- ON REMOTE TO SET #00

TOSHIBA
TW40F80
N5SS
DEAD SET
CHECK/REPLACE Q602 (LA4282 P/N# 23318413), F899 (5A GMA FUSE P/N# 23144735)

Toshiba
Model:CE35D10
Chassis:
No video/audio, slick screen, can't change on-screen display
Fix: ICV01, TA8851BN, Part # B0384763

Toshiba
Model:CE2058
Chassis:TAC8804
Dead no relay click
Q802 STRD1005T short pin 1 to 2 and C822 100ufd 16WV
Comments:Other elec. caps cause no start - C840, C863 or C866. Used Sams 2627 for print and covers this model close enough to troubleshoot.

Toshiba
Model:CX32G60
Chassis:
PINCUSSION EXPLODED
REPLACE ...Q462...2SC1740

Toshiba
Model:CX32G60
Chassis:
Pincushion (similar to the RCA problem)
Replace Q462 - 2SC1740 - NTE 85

Toshiba
CF2765K
9010
poor vertical linearity
C308 220uf 35V high temp. and also C301 1uf 50V

Toshiba
Model:CF2666R
9102
poor vertical linearity
Replaced C342 1uf. 50V also check or just replace C305 1uf 50V,
Comments:I've had some models use C301 instead of C342.

Toshiba
Model:35D-50
Chassis:
Dead, unplugging and re-plugging set causes set to come up & instantly shut down
Replace D310 22v 1/2w zener
Comments: Diode is physically located in the vertical B+ section.

Toshiba
Toshiba CF1926A
Chassis: ?
Only 2in vert. sweep
replace c301 2.2 uf at 50v

Toshiba
Model:mv19k2r
Chassis:n/a
HOT shorted or shutdown
replace HOT with heaver part ie 2sd1879 and R520 (0.82 1W)
Comments:the HOT will blow after replacing it whe set will come on but shut down r520 will increse in value had one that read 3 ohm but would shutdown replcace resistor works great

Toshiba
Model:CE2600C
Chassis:NA
No color
Replaced C260 .47@50 volts
Comments:located off pin 10 of the flyback

Toshiba
Model:TZ50V51
Chassis:N9SS YEAR 1999
DEAD, SET
REPLACE YOKE'S IF BAD PART # TDY767AS $16.00 EACH
Comments:WHEN A YOKE GOES BAD CAN CAUSE A HEAT BREAK OF crt

Toshiba
Model:CF3254 Year 1989
Chassis:
Vertical roll or vert drawn up from bottom
C301 and C305 2.2 mfd @ 50vdc.
Comments:This is common on lot's of Toshiba TV's brought in for any type of vertical trouble. C301 is located close to video ic. C305 is close to vert chip.

Toshiba
Model: C227T31
Chassis: TAC9905
Wavy horizontal line.(Vertical collapse).
Look for open wire under epoxy on left side of yoke. Reconnect.

Toshiba
Model:27h50
Chassis:
horizontal out blowed (ma

  • Re: TOSHIBAAnonymous, Tue Jan 13 7:44pm
    TOSHIBA CX2785B N/A BUZZING NOISE FROM SPEAKER SWITCH WITH SPEAKER SWITCH IN THE OFF MODE ADD A JUMPER BETWEEN THE NEGATIVE SIDE OF C641 AND THE NEGATIVE SIDE OF C637 TOSHIBA CX2786 N/A POOR VERTICAL ... more
    • Re: TOSHIBA — Anonymous, Tue Jan 13 7:48pm
      • remote sensormary, Thu Apr 8 3:05pm
        remote sensor appears to not be working. We cannot get it to respond to any universal remotes and no longer have the original remote. Is is possible that the sensor needs replacing. Any suggestions.... more
      • C227T31Jay, Fri Jul 3 7:35pm
        Remote control no longer turns TV on/off and does not change channels - everything else on remote control works - batteries have been changed several times Can anyone tell me what the problem is and... more
      • Re: TOSHIBAAnonymous, Tue Jan 13 7:57pm
        Toshiba 27h50 horizontal out blowed (many times) check & change ac 110v power plug and add 470 uf from base of 12v reg to gnd Comments:bad contact on ac plug generate supply peaks that deteriorates... more
        • CX32C81Anonymous, Mon Oct 27 10:44am
          no sound, No picture green line goes straight across the middle of the tv
          • Re: CX32C81Anonymous, Tue Oct 28 9:46am
            Sounds like no vertical sweep. Check vertical ic and it blown side of ic must check for open resistor and shorted diode feeding dc to vertical. Now also would check qf03 9v regulator for poor... more
        • ToshibaAnonymous, Mon Sep 6 11:37am
          Toshiba CE32T11 Customer Complaint: Dead set The TV was dead except that the power LED was on. After checking the standby power and finding it to be ok, I found that there was no drive to the power... more
Click here to receive daily updates